Rubber Tensile Tester
Up to ASTM, ISO, EN standards
Rubber Tensile Test Equipment
1 year free service
Port: Shenzhen
Minimum Order Quantity: 1 Set/Sets Haida
Supply Ability: 160 Set/Sets per Month Haida
Payment Terms: L/C,D/P,T/T
Contact Supplier
Packaging Detail: Standard export wooden case
Delivery Detail: within 15 days when deposit is confirmed
Rubber Tensile Tester
Rubber Tensile Tester UTS), often shortened to tensile strength (TS) or ultimate strength, is the maximum stress that a material can withstand while being stretched or pulled before necking, which is when the specimen's cross-section starts to significantly contract. Tensile strength is the opposite of compressive strength and the values can be quite different.
The UTS is usually found by performing a tensile test and recording the stress versus strain; The highest point of the stress-strain curve is the UTS. It is an intensive property; Therefore its value does not depend on the size of the test specimen. However, it is dependent on other factors, such as the preparation of the specimen, the presence or otherwise of surface defects, and the temperature of the test environment and material.
Tensile strengths are rarely used in the design of ductile members, but they are important in brittle members. They are tabulated for common materials such as alloys, composite materials, ceramics, plastics, and wood.
Parameters of Rubber Tensile Tester
| Capacity (optional) | 50kg, 100kg, 200kg, 500kg, 1T, 2T |
| Unit (Switchable) | G, KG, N, LB |
| Load Resolution | 1/100, 000 |
| Load Accuracy | ≤ 0.5% |
| Stroke (include the grips) | 1000 mm |
| Stroke Resolution | 0.5 mm |
| Sample Rate | 16 times/sec |
| Test Speed | 0.1~500 mm/min selectable |
| Effective Width | 1000mm (Excluding fixture) |
| Operation Mode | PC |
| Weight | 150kg |
| Display | PC |
| Motor | Servo Motor |
| Dimension(W× D× H)-Main Unit | 985× 510× 1600mm |
| Power | 1 phase, 220V/49Hz |
| Accessories | Tensile grips 1 set |
Pictures of Rubber Tensile Tester
Model No.: DRK128
Features: test the abrasion of print ink, PS photosensitive coating and other relative coating.
Model No.: DRK124
Features: DRK124 Drop impact Tester /impact test machine
Drop Tester
dropping strength test
strength test
Model No.: GD-ND
Features: GD-ND Solidifying Point Tester/Solidifying Point Analyzer/Oil Solidifying Point Tester is used for sample in the range of room
Model No.: GBH
Features: 1) Tensile tester is lab testing equipment
2) Reliable to test tensile, compression, flexure, shear, peel, fatigue cycling etc
Model No.: LX-A
Features: Shore C Durometer for foam&sponge
Test range:0-100HW
Standard:ASTM D2240,ISO7619 and GB/T531-1999
Model No.: AGW
Features: It adopt advanced measurement technology and applicate to ISO9001.High accuracy&Redolution.
Model No.: GBB-F
Features: 1.Heat seal tester set with 5 different temperature to do heat sealing.
2.sealing machine for plastic,pouches
3.use friendly
Model No.: GD-4929A Dropping Point Tester
Features: GD-4929A Dropping Point Tester (Oil Bath) is suitable to determine dropping point of lubricating grease and petroleum oils.
Model No.: CRS600
Features: high technical common rail tester
1.all computer control
2.screen display oil counting
Model No.: CRS2000
Features: common rail general test bench(TLD-CRS2000)
1.easy to operate
2.high technology
]3.test accurate
Model No.: CRS2000
Features: common rail general test bench(TLD-CRS2000)
1.easy to operate
2.high technology
]3.test accurate
Model No.: CRS2000
Features: common rail general test bench(TLD-CRS2000)
1.easy to operate
2.high technology
]3.test accurate